WRAP AROUND ROLLER SHUTTER DOOR SEAL
BUYERS FROM THE FOLLOWING AREAS NEED TO BE AWARE OF SURCHARGES TO SHIPPING COSTS IF SELECTING EXPRESS DELIVERY ON ANY THE SIZES 4 5 AND 10 METRES AS THOSE SIZES NEEDS SHIPPING VIA COURIER.
PLEASE CONTACT US FOR PRICES.
NORTHERN IRELAND THE CHANNEL ISLANDS SCOTTISH ISLANDS AND THE HIGHLANDS.
AB30-38 AB44-56 FK17-99 G83 HS1-9 IV1-28 IV30-30-56 IV63
KA27-28 KW1-17 PA20-49 PA60-78 PH18-26 PH30 PH42-44 ZE1-3.
We sell the Wrap around Roller Shutter Door Seal in lengths from 1 metre to 10 metres.
The Roller Shutter Wrap Around Seals Are Suitable For:
Any commercial roller doors with standard 75 mm T-bar bottom section.
Please note: If you order several 1 metre lengths you will receive that number of 1 metre lengths. NOT a linear length adding up to that total.
The Problems Roller shutters have are.
Rain penetration is a major cause of dampness in private and commercial garages but as it is different from other forms of dampness such as condensation and rising damp a different solution is required. Often the interface between the floor of a warehouse and a door is the source of water penetration. Rain will run vertically down the face of a door and then be driven by the wind into a garage. Left unchecked water intrusion may degrade packaging materials furniture and equipment. Surface water is also a potential slip hazard. Also some shutters do not sit flat to the ground their full length and so allow for rodents to enter the building and the wind to blow dust and leaves into the building.
The Wrap-Around Roller Shutter Seal fits all standard 75 mm T-bar surfaces on the underside of roller shutter doors.
It is quick and easy to fit and no fixings or sealants are required.
If a â€œT-barâ€ runs the length of the underside of a roller shutter garage door then a theft proof durable thermoplastic wrap-around seal is the solution.
You can also fit a threshold seal to further stop water ingress .
The Product & Its Purpose
- The Roller Shutter Wrap-Around Door Seal has been designed to form a watertight seal between the commercial roller door and the floor.
- The Roller Shutter Wrap-Around Door Seal prevents water leaves dust and debris from being blown under the garage door. Specifically it eradicates the damaging effects of wind-blown rainwater.
- It also prevents rodents from entering the warehouse.
- The Roller Shutter Wrap-Around Door Seal reduces the damaging effects of condensation (i.e. rusting) by keeping the warehouse equipment tools and some packaging (such as cardboard boxes) protected.
- Additionally energy costs may be reduced as a result of heat conservation and draft reducing.
The Roller Shutter Wrap-Around Door Seal is available in 5 lengths from 1 Metres - 5 Metres and has a depth of 30 mm to provide a seal that bridges gaps between the roller door and the floor with a rubber kick out fin for additional protection.
The gap between a Roller Shutter and a floor is usually anywhere from 5-10 mm in some places as most warehouse floors are not perfectly level.
When the door is fitted square it can create a gap between the door and the floor. This gap needs to be sealed.
This Roller Shutter Wrap-Around Door Seal is designed to seal gaps of up to 30 mm.
The Wrap-Around Door Seal wraps around the T-bar on bottom sections of the roller creating a tight fit. The â€˜u shapeâ€™ compresses down when the door closes creating a tight seal with the floor. The bottom of the seal has an additional rubber kick out fin which helps to create a watertight seal preventing rain leaves dust and debris from being blown under the door. This will keep the warehouse clean and dry and of course protect your equipment products and tools from the damaging effects of condensation and damp.
The Thermoplastic (Material);
The door seal is made from high quality thermoplastic that is both environmentally friendly and recyclable.
The material is also UV stabilised for extended life.
The Wrap-Around Thermoplastic Bottom Seal fits all standard 75 mm T-bar bottom sections of commercial roller doors.
It is very quick and easy to fit with no fixings/ sealant is required.
Just cut to length and then insert the back of the T bar into the rubber slot and then wrap around to fit the front of the T bar into the slot
- Tape measure.
- A pair of sharp scissors/stanley knife